Kwikset 914TRL User Manual Page 1

49526 / 01INSTALLATION GUIDE • GUÍA DE INSTALACIÓNRQACDBEFGHJMLNPKTools NeededHerramientas necesariasAAAAAAAAUse and programming instructions are loca

MInsert key and test latch. If latch does not extend or retract smoothly, adjust screws (H). Remove key when finished and make sure the latch bolt is

MInsert key and test latch. If latch does not extend or retract smoothly, adjust screws (H). Remove key when finished and make sure the latch bolt is

Z-Wave locks only: Temporarily install battery packSolo cerraduras Z-Wave:Instale temporalmente el conjunto de baterías Perform the Inclusion Proces

Z-Wave locks only: Temporarily install battery packSolo cerraduras Z-Wave:Instale temporalmente el conjunto de baterías Perform the Inclusion Proces

JJLay excess cable flat inside the bottom of the interior housing (J).Acomode el exceso de cable en el fondo del alojamiento interior (J).Ensure tight

JJLay excess cable flat inside the bottom of the interior housing (J).Acomode el exceso de cable en el fondo del alojamiento interior (J).Ensure tight

A BLYESSiNONoNote: “Inclusion” refers to the process in which the lock is added to a Z-Wave or ZigBee controller. “Exclusion” refers to the process in

A BLYESSiNONoNote: “Inclusion” refers to the process in which the lock is added to a Z-Wave or ZigBee controller. “Exclusion” refers to the process in

MNPQx3ball tippunta de bolaIf needed, rekey the lock to work with your existing key. See the supplied SmartKey Rekey instructions for more information

MNPQx3ball tippunta de bolaIf needed, rekey the lock to work with your existing key. See the supplied SmartKey Rekey instructions for more information

Options for Select Models OnlyOpciones solamente para modelos selectosDo not use electric drill or electric screwdriver to tighten screws.No utilice e

FoldDoble1-3/4" (44 mm)1-3/8" (35 mm)2-3/8" (60 mm)2-3/4" (70 mm)Edge • Borde BacksetDistancia al centroFace • Frente CenterlineLi

FoldDoble1-3/4" (44 mm)1-3/8" (35 mm)2-3/8" (60 mm)2-3/4" (70 mm)Edge • Borde BacksetDistancia al centroFace • Frente CenterlineLi

Options for Select Models OnlyOpciones solamente para modelos selectosDo not use electric drill or electric screwdriver to tighten screws.No utilice e

1"25 mm2-1/8"54 mm1-1/2"38 mm1-3/8" – 1-3/4"35 mm – 44 mm2-3/8" (60 mm)or • o 2-3/4" (70 mm)oro180°Check Dimensions

1"25 mm2-1/8"54 mm1-1/2"38 mm1-3/8" – 1-3/4"35 mm – 44 mm2-3/8" (60 mm)or • o 2-3/4" (70 mm)oro180°Check Dimensions

1-1/2"38 mmATest if latch bolt fully extends and retracts. Chisel out area inside hole as needed so latch can operate smoothly.Pruebe si el perno

1-1/2"38 mmATest if latch bolt fully extends and retracts. Chisel out area inside hole as needed so latch can operate smoothly.Pruebe si el perno

GECable goes underneath latchEl cable va por debajo del pestilloRoute cable through center hole, then push cable into bottom hole.Conecte el cable a t

GECable goes underneath latchEl cable va por debajo del pestilloRoute cable through center hole, then push cable into bottom hole.Conecte el cable a t